Ford Explorer: Climate Control System - General Information / General Procedures - Air Conditioning (A/C) Odor Treatment - Vehicles With: R134A Refrigerant

Ford Explorer 2020-2024 Service Manual / Electrical / Climate Control System / Climate Control System - General Information / General Procedures - Air Conditioning (A/C) Odor Treatment - Vehicles With: R134A Refrigerant

Special Tool(s) / General Equipment

A/C Odor Remover Flexible Applicator

Materials

Name Specification
Motorcraft® A/C Cooling Coil Coating
YN-29
-
 

Inspection

NOTE: There are typically 4 types of objectionable odors found in a vehicle:

  • chemical odors
  • environmental odors
  • human and other interior-generated odors
  • microbiological odors
Before determining that A/C odor treatment is required, determine the source and the circumstances under which the odor occurs.

NOTE: Chemical odors are usually constant regardless of the climate control system setting although they may be enhanced by A/C operation. Most chemical odors are caused by fluid leaks or incorrectly cured adhesives. Chemical odors can be eliminated by repairing the leaking component and removing any residue.

NOTE: Environmental odors usually occur for a short time and diminish after the vehicle passes through the affected area. These odors are typically only detected when the vehicle windows are open, or when the climate control system is operating in a mode that allows for fresh air. Environmental odors cannot be eliminated because they are external in source, but they may be minimized by switching to a climate control setting that uses recirculated air.

NOTE: Human and other interior-generated odors occur while the source is present and may linger for a short time after. These odors may be more noticeable during A/C operation. Human odors may be eliminated by removing the source and cleaning the affected area.

NOTE: Microbiological odors, if in the A/C system, usually last for about 30 seconds after the system is turned on. They are detected while the A/C is turned on and using either outside or recirculated air. Microbiological odors that occur in areas other than the A/C system (for example, water in doors or wet carpeting) may last indefinitely and are more intense when recirculated air is used. Microbiological odors are not present at temperatures at or below 10° C (50° F).

Microbiological odors can be eliminated by removing the source and treating the affected area. Allow standing water to drain and dry out. A/C systems may be treated by using Motorcraft® A/C Cooling Coil Coating (YN-29) as described in the service procedure below.

NOTE: Microbiological odors result from microbial growth supported by warm temperatures and moisture. Microbiological odors are described as musty/mildew type smells and may occur on/in:

  • foam seals
  • rubber seals
  • adhesives
  • standing water
  • water soaked carpet/trim
  1. Identify the type of odor present in the vehicle. Do not proceed with A/C odor treatment if the odor source is found to be outside of the A/C system. Refer to the following list for examples.
    Odor Source Odor Description
    Chemical Odors
    Coolant Sweet smell
    Fuel Gasoline or diesel fuel smell
    Oil Oil type or burning smell
    Power Steering Fluid Oil type or burning smell
    Transmission Fluid Oil type or burning smell
    Washer Fluid Alcohol type smell
    Gear Lube Garlic/sulfur smell
    Refrigerant Oil Ether type smell
    Carpet/trim Adhesives Fishy, urine or sweet smell
    Evaporator Core Coating Wet cement type smell
    Environmental Odors
    Exhaust Exhaust, fuel or burning type smell
    Industrial Pollutants Various smells
    Dust Musty, mildew or wet cement type smell
    Pollen Sweet smell
    Tobacco Burning, tar smell
    Human and Other Interior Generated Odors
    Body Secretions Body odor
    Perfuming Agents Sweet or fragrance smell
    Clothing Musty, mildew or body odors
    Food/Beverage Sweet, musty, mildew or fishy smell
    Microbiological Odors
    Microbiological Odors Occurring Inside of A/C System Musty, mildew smell lasting about 30 seconds after A/C is turned on
    Microbiological Odors Occurring Outside of A/C System Musty, mildew smell lasting indefinitely and possibly more pronounced when using recirculated air

Repair

  1. NOTE: Identify the source of the odor.

    • Check the evaporator core drain tube for restriction.
    • Check the passenger and driver side carpet for moisture. If moisture is found, A/C odor treatment is not necessary. Diagnose for a water leak as needed.
    • Check the cabin air filter and cabin air filter cover for moisture resulting from water bypassing the cowl baffling system. If moisture is found, A/C odor treatment is not necessary. Diagnose for a water leak as needed.
    • Check the cowl top panel and air inlet screen for standing water or foreign material. If necessary, remove the wiper cowl panel to remove any standing water and clean the air inlet screen using a wet/dry vacuum. Refer to appropiate section in Group 501 for the procedure.
  1. Open all vehicle windows and doors.
  1. Make sure the A/C is off.
  1. Select REGISTER mode (A/C off).
  1. Adjust the temperature setting to full warm.
  1. Adjust the blower motor speed to HI.
  1. Run the engine for 25 minutes to dry out the A/C system.
  1. Turn the ignition OFF.
  1. Remove the cabin air filter. Refer to the appropriate section in Group 412 for the procedure.
  1. NOTICE: To avoid damage, do not spill or spray this product on the blower motor speed control.

    Remove the blower motor speed control. Refer to the appropriate section in Group 412 for the procedure.
  1. NOTICE: To avoid damage to the vehicle interior, do not spill or spray this product on any interior surface.

    NOTE: Only Motorcraft® A/C Cooling Coil Coating (YN-29) is approved for use on Ford vehicles. No other coating is approved. Use of other coatings may cause damage to the factory coating and more odor issues.

    Add one full bottle of Motorcraft® A/C Cooling Coil Coating (YN-29) to the A/C Odor Remover Flexible Applicator tool.
    • 258‐62644 A/C Odor Remover Flexible Applicator
      Use the General Equipment: A/C Odor Remover Flexible Applicator
      Material: Motorcraft® A/C Cooling Coil Coating / YN-29
  1. Insert the nozzle into the evaporator housing and direct the spray toward the evaporator core face. Spray the entire evaporator core face until empty.
  1. Install the blower motor speed control. Refer to the appropriate section in Group 412 for the procedure.
  1. Repeat Steps 4 through 8 to cure the cooling coil coating.
  1. Install the cabin air filter. Refer to the appropriate section in Group 412 for the procedure.

    General Procedures - Air Conditioning (A/C) Odor Treatment - Vehicles With: R1234YF Refrigerant

    Special Tool(s) / General Equipment A/C Odor Remover Flexible Applicator Materials Name Specification Motorcraft® A/C Cooling Coil CoatingYN-29 -  Inspection NOTE: ..

    General Procedures - Air Conditioning (A/C) System Flushing - Hybrid Electric Vehicle (HEV), Vehicles With: R1234YF Refrigerant

    Special Tool(s) / General Equipment Air Conditioning Flush and Purge Service Unit Air Conditioning Adaptor Kit Materials Name Specification Motorcraft® A/C System Flushing Solv..

    Other information:

    Ford Explorer 2020-2024 Service Manual: Description and Operation - Body Closures - System Operation and Component Description


    System Operation System Diagram Item Description 1 RGTM 2 Front Power Liftgate Switch 3 Exterior Liftgate Release Switch 4 Anti-Pinch Switches 5 BCM 6 Left/Right Power Liftgate Motors 7 Power Liftgate Latch 8 Cinch Motor 9 Latch/Cinch Switches 10 Hands-Free Liftgate Actuation Module 11 Hands-Free Liftgate Actuatio..

    Ford Explorer 2020-2024 Service Manual: Specifications


      Lubricants, Fluids, Sealers and Adhesives Item Specification Transfer case fluid   Material: Motorcraft® MERCON® LV Automatic Transmission Fluid / XT-10-QLVC (WSS-M2C938-A) (MERCON® LV, )   Capacities   Liters Transfer case - Service fill 1...

    Categories

    Integrated Keyhead Transmitter (If Equipped)

    Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control.

    read more

     
    Copyright © 2024 www.foexplorer.com